Editor’s Choice Articles

There is an increasing need for the development of novel technologies for tunnel construction in difficult geological conditions to protect segmental linings from unexpected large deformations. In the context of mechanized tunneling, one method to increase the damage tolerance of tunnel linings in such conditions is the integration of a compressible two-component grout for the annular gap between the segmental linings and the deformable ground. In this regard, expanded polystyrene (EPS) lightweight concrete/mortar has received increasing interest as a potential “candidate material” for the aforementioned application. In particular, the behavior of the EPS lightweight composites can be customized by modifying their pore structure to accommodate deformations due to specific geological conditions such as squeezing rocks. To this end, novel compressible cementitious EPS-based composite materials with high compaction potential have been developed. Specimens prepared from these composites have been subjected to compressive loads with and without lateral confinement. Based on these experimental data a computational model based on the Discrete Element Method (DEM) has been calibrated and validated. The proposed calibration procedure allows for modeling and prognosis of a wide variety of composite materials with a high compaction potential. The calibration procedure is characterized by the identification of physically quantifiable parameters and the use of phenomenological submodels. Model prognoses show excellent agreement with new experimental measurements that were not incorporated in the calibration procedure. Full article

The results of studies on the synthesis and characterization of conductive polymer composite materials designed as potential separators for lithium ion batteries are presented. The conductive polymer composites were prepared from UV-cured poly(siloxane-urethanes)s (PSURs) containing poly(ethylene oxide) (PEO) segments and modified with lithium salts and ionic liquids (ILs). The most encouraging results in terms of specific conductivity and mechanical properties of the composite were obtained when part of UV-curable PSUR prepolymer was replaced with a reactive UV-curable IL. Morphology of the composites modified with ILs or containing a standard ethylene carbonate/dimethyl carbonate mixture (EC/DMC) as solvent was compared. It was found that the composites showed a two-phase structure that did not change when non-reactive ILs were applied instead of EC/DMC but was much affected when reactive UV-curable ILs were used. The selected IL-modified UV-cured PSUR composite that did not contain flammable EC/DMC solvent was preliminarily tested as gel polymer electrolyte and separator for lithium ion batteries. Full article

Energy harvesting systems for low-power devices are increasingly being a requirement within the context of the Internet of Things and, in particular, for self-powered sensors in remote or inaccessible locations. Triboelectric nanogenerators are a suitable approach for harvesting environmental mechanical energy otherwise wasted in nature. This work reports on the evaluation of the output power of different polymer and polymer composites, by using the triboelectric contact-separation systems (10 N of force followed by 5 cm of separation per cycle). Different materials were used as positive (Mica, polyamide (PA66) and styrene/ethylene-butadiene/styrene (SEBS)) and negative (polyvinylidene fluoride (PVDF), polyurethane (PU), polypropylene (PP) and Kapton) charge materials. The obtained output power ranges from 0.2 to 5.9 mW, depending on the pair of materials, for an active area of 46.4 cm². The highest response was obtained for Mica with PVDF composites with 30 wt.% of barium titanate (BT) and PA66 with PU pairs. A simple application has been developed based on vertical contact-separation mode, able to power up light emission diodes (LEDs) with around 30 cycles to charge a capacitor. Further, the capacitor can be charged in one triboelectric cycle if an area of 0.14 m² is used. Full article

To meet sustainability objectives in the transport sector, natural fiber (NF) and recycled carbon fiber (RCF) have been developed, although they have been typically limited to low to medium performance components. This work has considered the effect of interlayer hybridization of woven NF and non-woven RCF with woven virgin carbon fibers (VCF) on the mechanical and damping performance of hybrid laminates, produced using double bag vacuum infusion (DBVI). The mean damping ratio of the pure laminates showed a trend of NF>RCF>VCF, which was inversely proportional to their modulus. The tensile, flexural and damping properties of hybrid laminates were dominated by the outermost ply. The VCF-RCF and VCF-NF hybrid laminates showed a comparatively greater mean damping ratio. The results of this work demonstrate a method for the uptake of alternative materials with a minimal impact on the mechanical properties and improved damping performance. Full article

This article details the preparation of hollow gold-silver nanoshells (GS-NSs) coated with tunably thin silica shells for use in plasmon-enhanced photocatalytic applications. Hollow GS-NSs were synthesized via the galvanic replacement of silver nanoparticles. The localized surface plasmon resonance (LSPR) peaks of the GS-NSs were tuned over the range of visible light to near-infrared (NIR) wavelengths by adjusting the ratio of silver nanoparticles to gold salt solution to obtain three distinct types of GS-NSs with LSPR peaks centered near 500, 700, and 900 nm. Varying concentrations of (3-aminopropyl)trimethoxysilane and sodium silicate solution afforded silica shell coatings of controllable thicknesses on the GS-NS cores. For each type of GS-NS, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images verified our ability to grow thin silica shells having three different thicknesses of silica shell (~2, ~10, and ~15 nm) on the GS-NS cores. Additionally, energy-dispersive X-ray (EDX) spectra confirmed the successful coating of the GS-NSs with SiO₂ shells having controlled thicknesses. Extinction spectra of the as-prepared nanoparticles indicated that the silica shell has a minimal effect on the LSPR peak of the gold-silver nanoshells. Full article

The aim of the study was to establish the influence of poly(ethylene glycol) (PEG) on the properties of potential biodegradable packaging materials with antibacterial properties, based on polylactide (PLA) and tea tree essential oil (TTO). The obtained polymeric films consisted of PLA, a natural biocide, and tea tree essential oil (5–20 wt. %) was prepared with or without an addition of 5 wt. % PEG. The PLA-based materials have been tested, taking into account their morphology, and their thermal, mechanical and antibacterial properties against Staphylococcus aureus and Escherichia coli. It was established that the introduction of a plasticizer into the PLA–TTO systems leads to an increase in tensile strength, resistance to deformation, as well an increased thermal stability, in comparison to films modified using only TTO. The incorporation of 5 wt. % PEG in the PLA solution containing 5 wt. % TTO allowed us to obtain a material exhibiting a satisfactory antibacterial effect on both groups of representative bacteria. The presented results indicated a beneficial effect of PEG on the antibacterial and functional properties of materials with the addition of TTO. Full article

Geopolymer, a nanoporous aluminosilicate filled with water and ions, has been selected as a potential matrix to encapsulate MgZr alloy fuel cladding. In this study, we investigate the evolution of the corrosion products formed during the corrosion of MgZr in poral solutions extracted from geopolymers with and without NaF as corrosion inhibitor. Using various characterization techniques such as Scanning Electron and Scanning Transmission Electron Microscopies coupled to Energy Dispersive X-ray spectroscopy and Grazing Incidence X-ray Diffraction, we show that the amounts of dissolved silica and fluoride species in solution are the key parameters driving the nature of corrosion products and probably their passivating properties regarding MgZr corrosion. Full article

Green revolution and high carbon footprint concepts have attracted the development of a green and sustainable environment. This work endeavors to investigate the behavior of recycled aggregate geopolymer concrete (RAGC) developed with four different types of effluents to develop sustainability in the construction industry and to produce an eco-friendly environment. Each of the types of effluents was used by completely replacing the freshwater in RAGC to examine its influence on compressive strength (CS), chloride ion migration (CIM), split tensile strength (STS), and resistance to the sulfuric acid attack of RAGC at various testing ages. The test outputs portray that the effluent obtained from the textile mill performed well for the CS (25% higher than the control mix) and STS (17% higher than the control mix) of RAGC. Similarly, the highest mass loss of RAGC due to the acid attack (41% higher than control mix) and the highest CIM (29% higher than control mix) were represented by the RAGC mix made with effluent obtained from fertilizer mill. The statistical analysis indicated no significant influence of using textile mill effluent (TE), fertilizer mill effluent (FE), and sugar mill effluent (SE) on the STS, CIM, and mass loss due to acid attack while it presented a significant influence on the CS of various mixes. Therefore, this investigation solidly substantiates the acceptability of studied types of effluents for the fabrication of eco-friendly green materials. Full article

A big amount of solid wastes or dump sludges is generated after leaching vanadium (V) from a roasted mixture. As the vanadium content in these tailings is comparable to its concentration in traditional vanadium sources such as titanomagnetite ores or a vanadium converter slag, these wastes could be recycled to extract additional vanadium. Therefore, this research was aimed on studies of vanadium-containing sludges resulting from hydrometallurgical production of vanadium pentoxide to find an optimal technology for V extraction. The material composition of industrial and synthetic sludge samples was studied by X-ray fluorescence analysis (XRF), X-ray diffraction (XRD), secondary ions mass spectroscopy (SIMS), and X-ray photoelectron spectroscopy (XPS, ESCA). The paper demonstrates the presence of vanadium in sludges, not only in spinels in 3+ oxidation degree, but also in other compounds containing V⁴⁺ and V⁵⁺. It was found that vanadium substitutes a set of elements in minerals except spinel. The dependence between the content of insoluble vanadium compounds and V oxidation degree was determined. Full article

Rubber from recycled car tires and styrene-butadiene-styrene (SBS) were used for the chemical modification of commercially available road bitumen 50/70 (EN 12591). The modification process began with the addition of rubber into asphalt and heating the whole amount at the temperature of 190 °C or 220 °C. Under such conditions, de-vulcanization of rubber took place. Next, SBS and sulfur as a cross-linker were added and the heating was continued so that cross-linking of SBS and the de-vulcanized rubber proceeded. In the studies on the influence of rubber concentration on the final properties of asphalt 10% or 15% of rubber was considered. Chemical modification reactions were performed within 2, 4, and 8 h. The results showed that both the modification at 190 °C and 220 °C affected the properties of the base asphalt efficiently, although the asphalt modified at 190 °C contained more non-degraded rubber. Increasing the modification time led to dissolution of the rubber crumbs and its de-vulcanization. Bitumens modified in this way are characterized by high storage stabilities. Their behavior at low temperatures also deserves attention. Full article

The presented paper summarizes the main research findings on the impact of the environment concerning the durability and service life of building joint sealants. The focus is placed on sealed joints in façade applications, which can serve different purposes and can also be several meters long which often intensifies the stresses that the joint needs to withstand and therefore its service life can be significantly shortened. Different approaches, test sample geometries and high-performance sealants, were used in this context to determine the most critical aspects for the studied application sector. The research was divided into three phases where the joints were subjected to (I) artificial weathering in a laboratory environment, (II) real weathering in an external environment, and (III) weathering via a real application that was monitored for almost 4 years. The extensive research scope confirmed one commonly known presumption, that standardized artificial weathering/aging methods are not able, from a long-term perspective, to simulate the impact of a real environment. The most valuable results were obtained in the third phase of the research, where the monitoring of a real façade brought to light completely different conclusions. The joints exposed to the real environment were either completely deteriorated or showed signs of advanced aging. Full article

The surface crack of ballastless track slab can seriously reduce the serviceability and durability of high-speed railway (HSR). Aiming at accurately and efficiently detecting the slab cracks, this research proposes an infrared thermography (IRT)-based method for the surface crack, which is the most serious and common crack type in track slab. A three dimensional finite element (FE) model of IRT detection of concrete slab with surface cracks is established. The relation between the width of detectable cracks and the ambient temperature can be thereby obtained by inputting the measured thermodynamic parameters in the model. Parametric study shows that with ambient temperature higher than 15 °C, cracks with a width of no less than 0.2 mm can be well detected. Scale model test and field test are conducted, IRT method can effectively locate the slab surface cracks with width as small as 0.14 mm when ambient temperature is no less than 20 °C. Full article

The development of novel biocompatible and biodegradable materials for medical applications has been drawing significant interest in the scientific community for years. Particularly, chitosan loaded with silver nanoparticles (Ag NPs) has a strong antimicrobial potential and could be applied, for example, as wound dressing material. In this work, chitosan/Ag NP composites were produced utilizing a single-step plasma-solution process, which is simple and environmentally friendly. An acetic solution of chitosan containing AgNO₃ was treated by the direct current (DC) atmospheric pressure glow discharge, with the liquid serving as either cathode or anode. The plasma-solution system with liquid anode is more useful for the production of Ag NPs. Nevertheless, the NP size is comparable for both cases. The plasma treatment with both polarities led to chitosan degradation. The cleavage of glucosidic chains mostly occurred in the system with the liquid cathode, whereas the side oxidation reactions took place when the solution served as the anode. The oxidation processes were possibly induced by the hydrogen peroxide H₂O₂ efficiently formed in the last case. The composite materials produced with both polarities of liquid electrode demonstrated the bactericidal action against Gram-negative Escherichia coli, Gram-positive Staphylococcus aureus, and Gram-positive Bacillus subtilis. Full article

Liquid resin infusion processes are becoming attractive for aeronautic applications as an alternative to conventional autoclave-based processes. They still present several challenges, which can be faced only with an accurate simulation able to optimize the process parameters and to replace traditional time-consuming trial-and-error procedures. This paper presents an experimentally validated model to simulate the resin infusion process of an aeronautical component by accounting for the anisotropic permeability of the reinforcement and the chemophysical and rheological changes in the crosslinking resin. The input parameters of the model have been experimentally determined. The experimental work has been devoted to the study of the curing kinetics and chemorheological behavior of the thermosetting epoxy matrix and to the determination of both the in-plane and out-of-plane permeability of two carbon fiber preforms using an ultrasonic-based method, recently developed by the authors. The numerical simulation of the resin infusion process involved the modeling of the resin flow through the reinforcement, the heat exchange in the part and within the mold, and the crosslinking reaction of the resin. The time necessary to fill the component has been measured by an optical fiber-based equipment and compared with the simulation results. Full article

Poly(acrylonitrile) (PAN) fibers have two essential drawbacks: they are usually processed by solution-spinning, which is inferior to melt spinning in terms of productivity and costs, and they are flammable in air. Here, we report on the synthesis and melt-spinning of an intrinsically flame-retardant PAN-copolymer with phosphorus-containing dimethylphosphonomethyl acrylate (DPA) as primary comonomer. Furthermore, the copolymerization parameters of the aqueous suspension polymerization of acrylonitrile (AN) and DPA were determined applying both the Fineman and Ross and Kelen and Tüdõs methods. For flame retardancy and melt-spinning tests, multiple PAN copolymers with different amounts of DPA and, in some cases, methyl acrylate (MA) have been synthesized. One of the synthesized PAN-copolymers has been melt-spun with propylene carbonate (PC) as plasticizer; the resulting PAN-fibers had a tenacity of 195 ± 40 MPa and a Young’s modulus of 5.2 ± 0.7 GPa. The flame-retardant properties have been determined by Limiting Oxygen Index (LOI) flame tests. The LOI value of the melt-spinnable PAN was 25.1; it therefore meets the flame retardancy criteria for many applications. In short, the reported method shows that the disadvantage of high comonomer content necessary for flame retardation can be turned into an advantage by enabling melt spinning. Full article

Metal additive manufacturing (MAM), also known as metal 3D printing, is a rapidly growing industry based on the fabrication of complex metal parts with improved functionalities. During MAM, metal parts are produced in a layer by layer fashion using 3D computer-aided design models. The advantages of using this technology include the reduction of materials waste, high efficiency for small production runs, near net shape manufacturing, ease of change or revision of versions of a product, support of lattice structures, and rapid prototyping. Numerous metals and alloys can nowadays be processed by additive manufacturing techniques. Among them, Al-based alloys are of great interest in the automotive and aeronautic industry due to their relatively high strength and stiffness to weight ratio, good wear and corrosion resistance, and recycling potential. The special conditions associated with the MAM processes are known to produce in these materials a fine microstructure with unique directional growth features far from equilibrium. This distinctive microstructure, together with other special features and microstructural defects originating from the additive manufacturing process, is known to greatly influence the corrosion behaviour of these materials. Several works have already been conducted in this direction. However, several issues concerning the corrosion and corrosion protection of these materials are still not well understood. This work reviews the main studies to date investigating the corrosion aspects of additively manufactured aluminium alloys. It also provides a summary and outlook of relevant directions to be explored in future research. Full article

The purpose of the conducted experiments was to test the selected properties of materials intended for porous sintered bearings containing layered materials in the form of powders with an average particle size of 0.5–1.5 μm, with very good tribological properties. The subject of the research was a sinter based on iron powder with the addition of layered materials; molybdenum disulfide MoS₂ (average particle size 1.5 μm), tungsten disulfide WS₂ (average particle size 0.6 μm), hexagonal boron nitride, h-BN (average particle size 0.5 and 1.5 μm) with two different porosities. The article presents the results of density and porosity tests, compressive strength, metallographic and tribological tests and the assessment of changes in the surface condition occurring during the long storage period. The use of layered additives allows for an approximately 20% lower coefficient of friction. In the case of sulfides, the technological process of pressing 250 MPa, 350 MPa, and sintering at a temperature of 1120 °C allows us to obtain a material with good strength and tribological properties, better than in the case of h-BN. However, the main problem is the appearance of elements from the decomposition of sulfide compounds in the material matrix, which results in rapid material degradation. In hexagonal boron nitride, such disintegration under these conditions does not occur; the material as observed does not degrade. In this case, the material is characterized by lower hardness, resulting from a different behavior of hexagonal boron nitride in the pressing and sintering process; in this case, pressing at a pressure of 350 MPa seems to be too low. However, taking into account that even with these technological parameters, the obtained material containing 2.5% h-BN with an average grain size of 1.5 μm allowed obtaining a coefficient of friction at the level of 0.41, which, with very good material durability, seems to be very positive news before further tests. Full article

The absence of sufficient knowledge of the heterogeneous damage behaviour of textile reinforced composites, especially under combined in-plane and out-of-plane loadings, requires the development of multi-scale experimental and numerical methods. In the scope of this paper, three different types of plain weave fabrics with increasing areal weight were considered to characterise the influence of ondulation and nesting effects on the damage behaviour. Therefore an advanced new biaxial testing method has been elaborated to experimentally determine the fracture resistance at the combined biaxial loads. Methods in image processing of the acquired in-situ CT data and micrographs have been utilised to obtain profound knowledge of the textile geometry and the distribution of the fibre volume content of each type. Combining the derived data of the idealised geometry with a numerical multi-scale approach was sufficient to determine the fracture resistances of predefined uniaxial and biaxial load paths. Thereby, Cuntze’s three-dimensional failure mode concept was incorporated to predict damage and failure. The embedded element method was used to obtain a structured mesh of the complex textile geometries. The usage of statistical and visualisation methods contributed to a profound comprehension of the ondulation and nesting effects. Full article

This paper presents a literature review concerning the characteristics of MgO (magnesium oxide or magnesia) and its application in cementitious materials. It starts with the characterization of MgO in terms of production processes, calcination temperatures, reactivity, and physical properties. Relationships between different MgO characteristics are established. Then, the influence of MgO incorporation on the properties of cementitious materials is investigated. The mechanical strength and durability behaviour of cement pastes, mortars and concrete mixes made with MgO are discussed. The studied properties of MgO–cement mixes include compressive strength, flexural strength, tensile strength, modulus of elasticity, water absorption, porosity, carbonation, chloride ion penetration, shrinkage, expansion, and hydration degree. In addition, microscopic analyses of MgO-cement mixes are also assessed. Summarizing the results of different studies, it is concluded that MgO incorporation in cementitious materials generally decreases the mechanical strength and shrinkage, and increases the porosity, expansion, carbonation and chloride ion migration. However, it should be emphasized that the properties of the specific MgO used (mainly the calcination temperature, the reactivity and the surface area) have a significant influence on the characteristics of the cementitious materials produced. Full article

Calcined clays are the only potential materials available in large quantities to meet the requirements of eco-efficient cement-based materials by reducing the clinker content in blended cements or reducing the cement content in concrete. More than 200 recent research papers on the idea of replacing Portland cement with large amounts of calcined clay are presented and discussed in detail. First, the fundamental information about the properties and structure of clay minerals is described. Then, the process of activation and hydration of clays is discussed, including the methods of pozzolanic activity assessment. Additionally, various testing methods of clays from different worldwide deposits are presented. The application of calcined clay in cement and concrete technology is then introduced. A separate chapter is devoted to lime calcined clay cement. Then an influence of calcined clay on durability of concrete is summarized. Finally, conclusions are formulated. Full article

We propose to use a bilayer insulator (2.5 nm Al₂O₃ + 35 nm SiO2) as an alternative to a conventional uni-layer Al₂O₃ (35 nm), for improving the performance and the reliability of GaN-on-Si semi vertical trench MOSFETs. This analysis has been performed on a test vehicle structure for module development, which has a limited OFF-state performance. We demonstrate that devices with the bilayer dielectric present superior reliability characteristics than those with the uni-layer, including: (i) gate leakage two-orders of magnitude lower; (ii) 11 V higher off-state drain breakdown voltage; and (iii) 18 V higher gate-source breakdown voltage. From Weibull slope extractions, the uni-layer shows an extrinsic failure, while the bilayer presents a wear-out mechanism. Extended reliability tests investigate the degradation process, and hot-spots are identified through electroluminescence microscopy. TCAD simulations, in good agreement with measurements, reflect electric field distribution near breakdown for gate and drain stresses, demonstrating a higher electric field during positive gate stress. Furthermore, DC capability of the bilayer and unilayer insulators are found to be comparable for same bias points. Finally, comparison of trapping processes through double pulsed and V_th transient methods confirms that the V_th shifts are similar, despite the additional interface present in the bilayer devices. Full article

Natural materials achieve exceptional mechanical properties by relying on hierarchically structuring their internal architecture. In several marine species, layers of stiff and hard inorganic material are separated by thin compliant organic layers, giving their skeleton both stiffness and toughness. This phenomenon is fundamentally based on the periodical variation of Young’s modulus within the structure. In this study, alteration of mechanical properties is achieved through a layer-wise build-up of two different materials. A hybrid 3D-printing device combining stereolithography and inkjet printing is used for the manufacturing process. Both components used in this system, the ink for jetting and the resin for structuring by stereolithography (SLA), are acrylate-based and photo-curable. Layers of resin and ink are solidified separately using two different light sources (λ₁ = 375 nm, λ₂ = 455 nm). Three composite sample groups (i.e., one hybrid material, two control groups) are built. Measurements reveal an increase in fracture toughness and elongation at break of 70% and 22%, respectively, for the hybrid material compared to the control groups. Moreover, the comparison of the two control groups shows that the effect is essentially dependent on different materials being well contained within separated layers. This bio-inspired building approach increases fracture toughness of an inherently brittle matrix material. Full article

In this paper, acoustic emission data fusion based on multiple measurements is presented for damage detection and identification in oxide-based ceramic matrix composites. Multi-AE (acoustic emission) sensor fusion is considered with the aim of a better identification of damage mechanisms. In this context, tensile tests were conducted on ceramic matrix composites, fabricated with 3M™ Nextel™ 610 fibers and aluminosilicate matrix, with two kinds of AE sensors. Redundant and complementary sensor data were merged to enhance AE system capability and reliability. Data fusion led to consistent signal clustering with an unsupervised procedure. A correlation between these clusters and the damage mechanisms was established thanks to in situ observations. The complementarity of the information from both sensors greatly improves the characterization of sources for their classification. Moreover, this complementarity allows features to be perceived more precisely than using only the information from one kind of sensor. Full article

The quasi-static penetration properties of hybrid laminates were experimentally investigated. Aramid fabrics, carbon fabrics, and short hemp fibres were applied as the reinforcements of hybrid and non-hybrid composite laminates with polyurethane–polyurea (PUR/PUA) matrix. The laminates were made by hand, in a mould. They were cured at room temperature for 24 h. Hybrid laminates consisted of aramid and carbon layers in two different configurations, i.e., aramid at the innermost layers and outermost layers. Aramid/PUR/PUA and carbon/PUR/PUA composites were fabricated for comparison purposes. Laminates were also prepared via an analogue sequence of laying the reinforcement layers with the addition of 5% by weight of hemp fibres in the PUR/PUA matrix. Quasi-static penetration tests (QSPT) were conducted using a tensile testing machine with a surface-hardened, hemispherical, steel punch (9 mm diameter tip), reflecting the geometry of the Parabellum projectile. A quasi-static puncture test was carried out until the laminate was perforated. The ratio between the support span (Ds) and the punch diameter (Dp) was SPR = Ds/Dp = 5.0. The results showed the influences of laminate hybridisation on the values of absorbed energy, punch shear strength, and damage mechanism in the QSPT test. The addition of hemp fibres to aramid laminates resulted in a positive hybridisation effect. The order of layers of aramid and carbon fabrics in hybrid laminates influenced the results obtained in the QSPT test. Full article

In this work, aligned discontinuous fibre composite (ADFRC) tapes were developed and investigated as precursors for a novel 3D printing filament. ADFRCs have the potential to achieve mechanical performance comparable to continuous fibre reinforced composites, given sufficient fibre length and high level of alignment, and avoid many of the manufacturing difficulties associated with continuous fibres, e.g., wrinkling, bridging and corner radii constraints. Their potential use for fused filament fabrication (FFF) techniques was investigated here. An extensive down-selection process of thermoplastic matrices was performed, as matrix properties significantly impact both the processing and performance of the filament. This resulted in four candidate polymers (ABS, PLA, Nylon, PETG) which were used to manufacture ADFRC tapes with a V_f of 12.5% using the high performance discontinuous fibre (HiPerDiF) technology and an in-house developed continuous consolidation module. Tensile stiffness and strength up to 30 GPa and 400 MPa respectively were recorded, showing that a discontinuous fibre filament has the potential to compete with continuous fibre filaments. Full article

Compositionally graded cylinders of Ti–Mn alloys were produced using the Laser Engineered Net Shaping (LENS™) technique, with Mn content varying from 0 to 12 wt.% along the cylinder axis. The cylinders were subjected to different post-build heat treatments to produce a large sample library of α–β microstructures. The microstructures in the sample library were studied using back-scattered electron (BSE) imaging in a scanning electron microscope (SEM), and their mechanical properties were evaluated using spherical indentation stress–strain protocols. These protocols revealed that the microstructures exhibited features with averaged chord lengths in the range of 0.17–1.78 μm, and beta content in the range of 20–83 vol.%. The estimated values of the Young’s moduli and tensile yield strengths from spherical indentation were found to vary in the ranges of 97–130 GPa and 828–1864 MPa, respectively. The combined use of the LENS technique along with the spherical indentation protocols was found to facilitate the rapid exploration of material and process spaces. Analyses of the correlations between the process conditions, several key microstructural features, and the measured material properties were performed via Gaussian process regression (GPR). These data-driven statistical models provided valuable insights into the underlying correlations between these variables. Full article

This paper proposes binary and ternary combinations of sewage sludge ash (SSA) with fly ash (FA), marble dust (MD) and rice husk ash (RHA) as partial replacements of Portland cement in concretes with a similar dosage to that used in precast blocks, with very dry consistency. Several physical-mechanical tests were carried out on concrete specimens with curing ages of 28 and 90 days: density, water absorption, capillary water absorption, ultrasonic pulse velocity and compressive strength. The combinations of residues significantly improve the properties of the cementitious systems: 30% replacement of Portland cement provides strength values similar to the reference sample, showing the synergetic effects of the combination of the mineral additions. The significance of this research relies on the combined use of the mineral additions as well as the use of them for the precast block industry. The results show synergies among the additions and even that some of them showed relevant improvements when they are used in combination, performing better than when used individually. Full article

Ti₂NiCu exhibits outstanding properties, such as superelasticity. Recently, its functional properties were also demonstrated on the nanoscale, a fact that makes it the preferred choice for numerous applications. Its properties strongly depend on the manufacturing route. In this work, phase analysis, inhomogeneity, and texture of melt-spun Ti₂NiCu ribbons were investigated using X-ray diffraction. Initially, the ribbons are amorphous. Passing an electric current result in controlled crystallization. Ribbons with 0%, 60%, and 96% crystallinity were studied. Both B2 austenite and B19 martensite phases were observed. Using grazing incidence X-ray diffraction, the inhomogeneity across the thickness was investigated and found to be substantial. At the free surface, a small presence of titanium dioxide may be present. Pole figures of 60% and 96% crystallinity revealed mostly strong fiber <100>_B2 texture in the thickness direction. These observations may be inferred from the manufacturing route. This texture is beneficial. The inhomogeneity across the thickness has to be considered when designing devices. Full article

We aim to examine the effects of a newly developed peptide derived from CPNE7 (Cpne7-DP) in tertiary dentin formation and peritubular space occlusion, and comprehensively evaluate its potential as a bioactive therapeutic agent. Human dental pulp cells (HDPCs) and a mouse pre-odontoblast cell line, MDPC-23, were chosen for in vitro studies to characterize lineage-specific cell responses after Cpne7-DP treatment. Whether Cpne7-DP reproduces the dentin regenerative potential of CPNE7 was tested using a beagle dog model by generating dentinal defects of various degrees in vivo. Peritubular space occlusion was further examined by scanning electron microscopy and microleakage test, while overall mineralization capacity of Cpne7-DP was tested ex vivo. CPNE7 promotes tubular dentin formation under both shallow and deep dentinal defects, and the functional peptide Cpne7-DP induces odontoblast-like differentiation in vitro, mineralization ex vivo, and tubular dentin formation in in vivo beagle dog dentin exposure and pulp exposure models. Moreover, Cpne7-DP leads to peritubular space occlusion and maintains stability under different conditions. We show that CPNE7 and its derivative functional peptide Cpne7-DP promotes dentin regeneration in dentinal defects of various degrees and that the regenerated hard tissue demonstrates the characteristics of true dentin. Limitations of the current dental materials including post-operative hypersensitivity make biological repair of dentin a field of growing interest. Here, we suggest that the dual functions of Cpne7-DP in tubular dentin formation and peritubular space occlusion are promising for the treatment of dentinal loss and sensitivity. Full article

The purpose of a battery thermal management system (BTMS) is to maintain the battery safety and efficient use as well as ensure the battery temperature is within the safe operating range. The traditional air-cooling-based BTMS not only needs extra power, but it could also not meet the demand of new lithium-ion battery (LIB) packs with high energy density, while liquid cooling BTMS requires complex devices to ensure the effect. Therefore, phase change materials (PCMs)-based BTMS is becoming the trend. By using PCMs to absorb heat, the temperature of a battery pack could be kept within the normal operating range for a long time without using any external power. PCMs could greatly improve the heat dissipation efficiency of BTMS by combining with fillers such as expanded graphite (EG) and metal foam for their high thermal conductivity or coordinating with fins. In addition, PCMs could also be applied in construction materials, solar thermal recovery, textiles and other fields. Herein, a comprehensive review of the PCMs applied in thermal storage devices, especially in BTMS, is provided. In this work, the literature concerning current issues have been reviewed and summarized, while the key challenges of PCM application have been pointed out. This review may bring new insights to the PCM application. Full article

Lithium metal batteries are considered “rough diamonds” in electrochemical energy storage systems. Li-metal anodes have the versatile advantages of high theoretical capacity, low density, and low reaction potential, making them feasible candidates for next-generation battery applications. However, unsolved problems, such as dendritic growths, high reactivity of Li-metal, low Coulombic efficiency, and safety hazards, still exist and hamper the improvement of cell performance and reliability. The use of functional separators is one of the technologies that can contribute to solving these problems. Recently, functional separators have been actively studied and developed. In this paper, we summarize trends in the research on separators and predict future prospects. Full article

The use of ecological materials for building and industrial applications contributes to minimizing the environmental impact of new technologies. In this context, the cement and geopolymer sectors are considering natural fibers as sustainable reinforcement for developing composites. Natural fibers are renewable, biodegradable, and non-toxic, and they exhibit attractive mechanical properties in comparison with their synthetic fiber counterparts. However, their hydrophilic character makes them vulnerable to high volumes of moisture absorption, thus conferring poor wetting with the matrix and weakening the fiber–matrix interface. Therefore, modification and functionalization strategies for natural fibers to tailor interface properties and to improve the durability and mechanical behavior of cement and geopolymer-based composites become highly important. This paper presents a review of the physical, chemical and biological pre-treatments that have been performed on natural fibers, their results and effects on the fiber–matrix interface of cement and geopolymer composites. In addition, the degradation mechanisms of natural fibers used in such composites are discussed. This review finalizes with concluding remarks and recommendations to be addressed through further in-depth studies in the field. Full article

Cold Bitumen Emulsion (CBE) mixture technologies have been recently developed to lower pavement construction temperatures to reduce environmental costs and control gas emissions. Due to its poor early mechanical strength, active fillers (i.e., cement) have been used to obtain high early stiffness in order to have the potential for timely construction of the next layer. There is, however, a lack of understanding about the impact of active fillers on the viscoelastic behavior and fatigue damage resistance of CBE mastics. This study, therefore, aims to identify the influence of active fillers on the rheological properties and the resulting fatigue behavior of CBE mastic, supported by chemical analysis for the filler-bitumen emulsion. For this aim, bitumen emulsion was mixed separately with seven fillers/blended fillers to prepare the CBE mastics. Various experiments, including continuous pH monitoring tests (chemical reactivity of filler-bitumen emulsion), Strain Sweep (SS) tests, Temperature-Frequency Sweep (TFS) tests, Time Sweep (TS) tests, and Linear Amplitude Sweep (LAS) tests were conducted on the CBE binder and the prepared mastics. Results show that the rheological performance and the fatigue damage resistance depend not only on the filler inclusions but also on filler type and chemistry. On this basis, the rise in complex shear modulus and the decrease in the viscous component is associated with a significant enhancement in fatigue performance for specific fillers. Full article

There is an increasing global trend to find sustainable, environmentally friendly and cost-effective materials as an alternative to limited natural raw materials. Similarly, the use of waste materials has been gaining popularity in the production of hot-mix asphalt (HMA). In this study, the sustainable use of glass-fiber-reinforced polyester (GRP) pipe waste powder (GRP-WP), gathered from the cutting and milling process of GRP pipe production, utilizing it in asphalt mixes as a filler, is evaluated based on lab testing to find out: (i) if it produces similar or better performance compared to the most conventionally available filler material (limestone) and, (ii) if so, what would be the optimum GRP-WP filler content to be used in asphalt mixes. For this reason, an experimental test matrix consisting of 45 samples with three different amounts of binder content (4%, 4.5% and 5.0%), and a 5% filler content with five different percentages of the GRP-WP content (0%, 25%, 50%, 75% and 100% replacement by weight of the filler), was prepared to figure out which sample would produce the similar Marshall stability and flow values compared to the control samples while also satisfying specification limits. It was found that the samples with 4.5% binder content, 3.75% GRP-WP and 1.25% limestone filler content produced the results both satisfying the specification requirements and providing an optimum mix design. It is believed that use of GRP-WP waste in HMA production would be a very useful way of recycling GRP-WP. Full article

Parent concrete coming from a wide range of sources can result in considerable differences in the properties of recycled coarse aggregate (RCA). In this study, the RCAs were obtained by crushing the parent concrete with water-to-cement ratios (W/C_parent) of 0.4, 0.5 and 0.6, respectively, and were strengthened by carbonation and nano-silica slurry wrapping methods. It was found that when W/C_paren was 0.3, 0.4 and 0.5, respectively, compared with the mortar in the untreated RCA, the capillary porosity of the mortar in the carbonated RCA decreased by 19%, 16% and 30%, respectively; the compressive strength of concrete containing the carbonated RCA increased by 13%, 11% and 13%, respectively; the chloride diffusion coefficient of RAC (D_RAC) containing the nano-SiO₂ slurry-treated RCA decreased by 17%, 16% and 11%; and that of RAC containing the carbonated RCA decreased by 21%, 25% and 26%, respectively. Regardless of being strengthened or not, both D_RAC and porosity of old mortar in RCAs increased with increasing W/C_parent. For different types of RCAs, D_RAC increased obviously with increasing water absorption of RCA. Finally, a theoretical model of D_RAC considering the water absorption of RCA was established and verified by experiments, which can be used to predict the D_RAC under the influence of different factors, especially the water absorption of RCA. Full article

New composites containing a natural filler made of diatom shells (frustules), permitting the modification of polylactide matrix, were produced by Fused Deposition Modelling (3D printing) and were thoroughly examined. Two mesh fractions of the filler were used, one of <40 µm and the other of 40−63 µm, in order to check the effect of the filler particle size on the composite properties. The composites obtained contained diatom shells in the concentrations from 0% to 5% wt. (0−27.5% vol.) and were subjected to rheological analysis. The composites obtained as filaments of 1.75 mm in diameter were used for 3D printing. The printed samples were characterized as to hydrophilic–hydrophobic, thermal and mechanical properties. The functional parameters of the printed objects, e.g., mechanical characteristics, stability on contact with water and water contact angle, were measured. The results revealed differences in the processing behavior of the samples as well as the effect of secondary granulation of the filler on the parameters of the printing and mechanical properties of the composites. Full article

Magnetorheological (MR) elastomers become one of the most powerful smart and advanced materials that can be tuned reversibly, finely, and quickly in terms of their mechanical and viscoelastic properties by an input magnetic field. They are composite materials in which magnetizable particles are dispersed in solid base elastomers. Their distinctive behaviors are relying on the type and size of dispersed magnetic particles, the type of elastomer matrix, and the type of non-magnetic fillers such as plasticizer, carbon black, and crosslink agent. With these controllable characteristics, they can be applied to various applications such as vibration absorber, isolator, magnetoresistor, and electromagnetic wave absorption. This review provides a summary of the fabrication, properties, and applications of MR elastomers made of various elastomeric materials. Full article

Biodegradable plastics can make an important contribution to the struggle against increasing environmental pollution through plastics. However, biodegradability is a material property that is influenced by many factors. This review provides an overview of the main environmental conditions in which biodegradation takes place and then presents the degradability of numerous polymers. Polylactide (PLA), which is already available on an industrial scale, and the polyhydroxyalkanoates polyhydroxybutyrate (PHB) and polyhydroxybutyrate-co-valerate (PHBV), which are among the few plastics that have been proven to degrade in seawater, will be discussed in detail, followed by a summary of the degradability of further petroleum-, cellulose-, starch-, protein- and CO₂-based biopolymers and some naturally occurring polymers. Full article

This article reviews the literature related to the performance of fiber reinforced concrete (FRC) in the context of the durability of concrete infrastructures. The durability of a concrete infrastructure is defined by its ability to sustain reliable levels of serviceability and structural integrity in environmental exposure which may be harsh without any major need for repair intervention throughout the design service life. Conventional concrete has relatively low tensile capacity and ductility, and thus is susceptible to cracking. Cracks are considered to be pathways for gases, liquids, and deleterious solutes entering the concrete, which lead to the early onset of deterioration processes in the concrete or reinforcing steel. Chloride aqueous solution may reach the embedded steel quickly after cracked regions are exposed to de-icing salt or spray in coastal regions, which de-passivates the protective film, whereby corrosion initiation occurs decades earlier than when chlorides would have to gradually ingress uncracked concrete covering the steel in the absence of cracks. Appropriate inclusion of steel or non-metallic fibers has been proven to increase both the tensile capacity and ductility of FRC. Many researchers have investigated durability enhancement by use of FRC. This paper reviews substantial evidence that the improved tensile characteristics of FRC used to construct infrastructure, improve its durability through mainly the fiber bridging and control of cracks. The evidence is based on both reported laboratory investigations under controlled conditions and the monitored performance of actual infrastructure constructed of FRC. The paper aims to help design engineers towards considering the use of FRC in real-life concrete infrastructures appropriately and more confidently. Full article

The aim of this study was to present the problem of durability of structural lightweight concrete made of a sintered fly ash aggregate. The issue of durability was researched for 12 concrete series in terms of their water absorption, water permeability, and freeze-thaw resistance. Additionally, the microstructure of several concretes was analyzed with a scanning electron microscope (SEM). In the durability research, the influences of the following parameters were taken into consideration: The initial moisture content of sintered fly ash (mc = 0, 17–18, and 24–25%); the aggregate grading (4/8 and 6/12 mm); and the water-cement ratio (w/c = 0.55 and 0.37). As a result of various compositions, the concretes revealed different properties. The density ranged from 1470 to 1920 kg/m³, and the corresponding strength ranged from 25.0 to 83.5 MPa. The durability research results of tested lightweight concretes showed that, despite considerably higher water absorption, a comparable water permeability and comparable or better freeze-thaw resistance in relation to normal-weight concrete may be present. Nevertheless, the fundamental requirement of lightweight concrete to achieve good durability requires the aggregate’s initial moisture content to be limited and a sufficiently tight cement matrix to be selected. The volume share of the cement matrix and aggregate, the cement content, and even the concrete strength are of secondary importance. Full article

The thermal and mechanical properties of polysiloxane foam are greatly improved by the addition of acrylolsobutyl polyhedral oligomeric silsesquioxane (MA0701, hereinafter referred to as MAPOSS), which has double bonds. The morphologies and properties of the polysiloxane composite foam were characterized. The average cell diameter of the composite foams decreased, while the cell density increased with increasing MAPOSS. Meanwhile, MAPOSS can enhance thermal conductivity and thermal stability. Thermal conductivity increased by 25%, and the temperature at the maximum weight loss rate increased from 556 °C to 599 °C. In addition, MAPOSS also promoted heterogeneous nucleation by functioning as a nucleating agent, which can increase cell density to improve the mechanical properties. The compressive strength of the composite foam increased by 170% compared with that of pure foam. In the composite, MAPOSS increased the cross-linking density by acting as a physical cross-linking point and limited the movement of the segments. Full article

This paper describes the process of additive manufacturing and a selection of three-dimensional (3D) printing methods which have applications in chemical synthesis, specifically for the production of monolithic catalysts. A review was conducted on reference literature for 3D printing applications in the field of catalysis. It was proven that 3D printing is a promising production method for catalysts. Full article

In this study, wet-ground carbide slag (i.e., WGCS) was utilized as an accelerator in calcium sulfoaluminate cement (CSA) for obtaining considerably faster setting processes for some special engineering processes such as plugging projects and rapid repair engineering. The WGCS–CSA system was designed, in which the replacement ratio of CSA by carbide slag was chosen as 4%, 8% and 12%. The setting time and compressive strength were measured, and the mechanism of the system hydration was studied in detail by means of calorimetry, XRD, thermogravimetry (TG) and SEM. The results showed that WGCS shortened the setting time of cement and significantly augmented the early strength. The addition of 8% of WGCS contributed to increasing the 2-h compressive strength from 4.2 MPa to 32.9 MPa. The decrease in the setting time and the increase in the initial strength were mainly attributed to the high initial pH value of the liquid phase and the high content of calcium ions in WGCS. Both these factors contributed to the ettringite formation and, at the same time, to the transformation of the morphology at a later time. Such results testify that WGCS can be used as an accelerator in the CSA system and also that it provides a novel approach to the reutilization of carbide slag. Full article

Recycled aggregate concrete (RAC) is a promising solution to address the challenges raised by concrete production. However, the current lack of pertinent design rules has led to a hesitance to accept structural members made with RAC. It would entail even more difficulties when facing application scenarios where brittle failure is possible (e.g., beam in shear). In this paper, existing major shear design formulae established primarily for conventional concrete beams were assessed for RAC beams. Results showed that when applied to the shear test database compiled for RAC beams, those formulae provided only inaccurate estimations with surprisingly large scatter. To cope with this bias, machine learning (ML) techniques deemed as potential alternative predictors were resorted to. First, a Grey Relational Analysis (GRA) was carried out to rank the importance of the parameters that would affect the shear capacity of RAC beams. Then, two contemporary ML approaches, namely, the artificial neural network (ANN) and the random forest (RF), were leveraged to simulate the beams’ shear strength. It was found that both models produced even better predictions than the evaluated formulae. With this superiority, a parametric study was undertaken to observe the trends of how the parameters played roles in influencing the shear resistance of RAC beams. The findings indicated that, though less influential than the structural parameters such as shear span ratio, the effect of the replacement ratio of recycled aggregate (RA) was still significant. Nevertheless, the value of v_c/(f_c)^1/2 (i.e., the shear contribution from RAC normalized with respect to the square root of its strength) predicted by the ML-based approaches appeared to be insignificantly affected by the replacement level. Given the existing inevitable large experimental scatter, more shear tests are certainly needed and, for safe application of RAC, using partial factors calibrated to consider the uncertainty is feasible when designing the shear strength of RAC beams. Some suggestions for future works are also given at the end of this paper. Full article

Crack healing has been studied extensively to protect reinforced concrete structures from the ingress of harmful ions. Research examining the regain in the mechanical properties of self-healing composites has focused mostly on the computation of the healing ratio based on the measurement of the tensile and compressive strengths but with poor regard for the flexural performance. However, the regain in the flexural performance should also be investigated for design purposes. The present study performs flexural testing on reinforced concrete members using crushed clinker binder and aggregates as well as crystalline admixtures as healing agents. Healing ratios of 100% for crack widths smaller than 200 μm and 85% to 90% for crack widths of 250 μm were observed according to the admixing of clinker binder and aggregates. Water flow test showed that the members replacing binder by 100% of clinker achieved the best crack healing performance. The crack healing property of concrete improved to some extent the rebar yield load, the members’ ultimate load and energy absorption capacity and ductility index. The crack distribution density from the observed crack patterns confirmed the crack healing effect provided by clinker powder. The fine grain size of clinker made it possible to replace fine aggregates and longer healing time increased the crack healing effect. Full article

In this study, powder metallurgy was used to fabricate titanium nitride/nickel metal-matrix composites. First, titanium and nickel powders with weight ratios of 20:80, 50:50 and 80:20 were dry mixed for 24 h. After cold isostatic pressing, the green compacts were soaked in a water-based hot forging lubricant and sintered at 850, 950 and 1050 °C for 1.5 h in an air atmosphere. The effects of the amounts of titanium powder and the sintering temperatures on the mechanical properties (hardness, wear resistance and compressive strength) of the composites were investigated. The results indicated that titanium gradually transformed into titanium nitride near the surface after sintering due to the carbothermal reduction reaction; this transformation was observed to significantly increase the hardness. In addition, an oxygen-rich film was observed to form between the titanium nitride particles and the nickel matrix. An optimum sintering temperature of 950 °C provides the composites (titanium–nickel weight ratios of 20:80) the best mechanical properties (wear resistance and compressive strength) among other groups. Furthermore, increasing the titanium content to 80% in the composite increased the hardness; however, the wear resistance and compressive strength decreased. Full article

The main applications of ionic liquids in chemistry and material research on one of the most important natural polymers—starch—are presented in this review. A brief characterization of ionic liquids and the advantages and disadvantages of using them in the modification and processing of polysaccharides is presented. The latest reports on the use of various ionic liquids as solvents or co-solvents; as media for synthesizing starch derivatives in oxidation, etherification, esterification, and transesterification, with particular emphasis on biocatalyzed reactions; and as plasticizers or compatibilizers in the processing of starch-based polymers have been investigated. The current trends, possibilities, and limitations of using this type of compound for the production of functional starch-based materials are presented. Full article

Nickel is one of the most dangerous environmental pollutants and its removal from wastewater is an important task. The capacity of a mineral–organic hybrid adsorbent, consisting of Shewanella xiamenensis biofilm and zeolite (clinoptilolite of the Chola deposit), to remove metal ions from nickel-containing batch systems under different experimental conditions was tested. The obtained biosorbent was characterized using neutron activation, SEM, and FTIR techniques. It was established that maximum removal of cations, up to 100%, was achieved at pH 6.0. Several mathematical models were applied to describe the equilibrium and kinetics data. The maximum adsorption capacity of the hybrid biosorbent, calculated using the Langmuir model, varied from 3.6 to 3.9 mg/g. Negative Gibbs energy values and positive ∆H° values indicate the spontaneous and endothermic character of the biosorption process. The effects of several parameters (pH and biosorbent dosage) on Ni(II) removal from real effluent, containing nickel with a concentration of 125 mg/L, were investigated. The optimal pH for Ni(II) removal was 5.0–6.0 and an increase of sorbent dosage from 0.5 to 2.0 led to an increase in Ni(II) removal from 17% to 27%. At two times effluent dilution, maximum Ni(II) removal of 26% was attained at pH 6.0 and sorbent dosage of 1.0 g. A 12-fold effluent dilution resulted in the removal of 72% of Ni(II) at the same pH and sorbent dosage values. The obtained hybrid biosorbent can be used for Ni(II) removal from industrial effluents with low Ni(II) concentrations. Full article

Heavy metal ions are not subject to biodegradation and could cause the environmental pollution of natural resources and water. Many of the heavy metals are highly toxic and dangerous to human health, even at a minimum amount. This work considered an optical method for detecting heavy metal ions using colloidal luminescent semiconductor quantum dots (QDs). Over the past decade, QDs have been used in the development of sensitive fluorescence sensors for ions of heavy metal. In this work, we combined the fluorescent properties of AgInS₂/ZnS ternary QDs and the magnetism of superparamagnetic Fe₃O₄ nanoparticles embedded in a matrix of porous calcium carbonate microspheres for the detection of toxic ions of heavy metal: Co²⁺, Ni²⁺, and Pb²⁺. We demonstrate a relationship between the level of quenching of the photoluminescence of sensors under exposure to the heavy metal ions and the concentration of these ions, allowing their detection in aqueous solutions at concentrations of Co²⁺, Ni²⁺, and Pb²⁺ as low as ≈0.01 ppm, ≈0.1 ppm, and ≈0.01 ppm, respectively. It also has importance for application of the ability to concentrate and extract the sensor with analytes from the solution using a magnetic field. Full article

The effect of welding speed on microstructure, mechanical properties, and corrosion properties of laser-assisted welded joints of a twinning-induced plasticity (TWIP) steel was investigated by using X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscattered diffraction (EBSD) analysis, electrochemical test, and micro-area scanning Kelvin probe test (SKP). The results reveal that the welded joints, with a fully austenitic structure, are obtained by laser welding. In addition, the preferred orientation of grains in fusion zone (FZ) increased with the increase of welding speed. Additionally, the coincidence site lattice (CSL) grain boundaries of FZ decreased with increasing welding speed. However, potentiodynamic polarization and SKP results demonstrated that the welding speed of 1.5 m/min renders superior corrosion resistance. It can also be inferred that the corrosion properties of the welded joints are related to the grain size and frequency of CSL grain boundary in FZ. Full article